Showing posts with label DIY Yeast Stir Plate. Show all posts
Showing posts with label DIY Yeast Stir Plate. Show all posts

Resurrecting Yeast

>> Thursday, May 14, 2009

Last year Wyeast did a limited edition release of New Belgium's Fat Tire yeast (WYXL1792). I'm a fan of Fat Tire and who knows when/if Wyeast will release this strain again. So I brewed a batch way back when it was originally released and decided I better try to save some for later.


I collected the yeast and stored it in the fridge in sanitized White Labs tubes. The yeast has been sitting in my fridge ever since and I noticed it was starting to turn more of a darker beige rather than the light tan normally associated with healthy yeast. I'm guessing this is due to the fact that the yeast is getting older. I remember a Basic Brewing podcast in which James Spencer was able to nurse an old yeast sample back to life. If I remember correctly, it was about a year or more old and his LHBS gave it to him for free. So I decided to give it a try and use my recently constructed stir plate to try to resurrect this strain.



I made a simple wort as described in John Palmer's how to brew. I pitched the yeast about 30 minutes ago, so time will tell if I'm able to bring this yeast back to life.





Update 5/26/2009: I haven't had time to brew a batch yet, but it seems as though I was able to nurse the Fat Tire yeast back to health. I added one White Labs sized sample of yeast and after a few days was able to harvest four+ samples. They probably have about 2/3 volume of a typical White Labs sample, so they'd benefit from a starter a few days before brew day. I'm going to try to brew a batch of my Microbus Amber this weekend. I'll post the results (hopefully good) as soon as I have them. I'm interested to see how stable this yeast is or if it will mutate after a few batches. My sample had a really nice bread/biscuit aroma, so hopefully that's a good sign.

Update 6/29/2009: I never did get around to brewing this batch but I saved the yeast yet again. So this one is still in limbo.

Read more...

Yeast Stir Plate Update

>> Tuesday, April 28, 2009

I finally got my stir bar for my DIY stir plate. The stir plate kept throwing my stir bar so I had to modify the magnet mounting slightly. Originally I mounted the magnets to the outside of the washer mounted on the PC fan. I ended up moving the magnets inward so that they meet at the axis of the rotating fan. I also replaced the original 12VDC power supply with a 6VDC one. The 12VDC power supply was just a little too powerful even when the rheostat was turned all the way down. Even with the 6VDC power supply, I get a nice little vortex from 25% on up. I'll be brewing a Rauchbier this weekend. Rauchbier is a German Smoked Lager and since it's a lager it's best to have a good sized yeast starter. So I'll probably fire up the starter tomorrow night (Wednesday) and brew on Saturday. Here's video of the stir plate in action.


Another update 2/22/2011: After accidentally losing a stir bar down the disposal last year I ordered a larger one with a pivot ring.  The new one is slightly over an inch long and seems to work much better in that the stir bar rarely gets thrown now.

Read more...

Yeast Stir Plate

>> Thursday, March 19, 2009

One item I've been planning on building for a while is a yeast stir plate. The purpose of the yeast stir plate is to boost the cell count in yeast starters resulting in higher pitch rates and healthier starters. This should reduce lag time before active fermentation begins and theoretically should improve the final product.


Commercial yeast stir plates can be fairly expensive so I'm going the DIY route. I wish I could claim I came up with the idea for the stir plate, but it's basically modeled after others on the web. The components and prices are as follows.


Disclaimer: I'm not an electrician and I can't guaranty the safety of this device. If you choose to build a similar device, do so at your own risk.



Here is a very basic wiring diagram that even non-technical people should be able to understand.




Click here for Steps 1-2

Read more...

Stir Plate - Step 1 - 2

I'm not going to go into a ton of detail because I figure most people that will attempt this project are somewhat technical and probably pretty handy. So here are the steps I used to build the stir plate:

1. I drilled a hole in the front of the project box for the rheostat. I also drilled a hole in the back for the power supply cord. Finally, I used a Dremel to cut out a relatively square-ish hole on the front for the power switch.


2. Next I connected the wiring...except for the fan. I didn't connect the fan at this point because it hadn't arrived yet. The connections on the rheostat are soldered, the switch uses female solderless terminals and I used a few crimp on connectors. I tried to keep things clean by using a few zip ties.


Click here for Steps 3-5

Read more...

Stir Plate - Steps 3 - 5

3. Next I mounted the fan. I chose to mount the fan to the bottom of the project box. A lot of the others I've seen have the fan mounted to the top of the project box but I wanted a cleaner look. Four #10 x 1.5 inch screws are inserted through the bottom of the box. A nut is tightened down on each screw on the inside of the box. Each screw is then screwed into the mounting holes on the fan frame. It seems pretty secure and I'll be able to adjust the height of the fan by a simple turn of the screws.

4. With the fan in place, the two wires are connected.

5. Next I attached the fender washer to the fan hub. I first tried mounting the washer using 5-minute epoxy and eyeballing the washer for center. This didn't work out very well because the washer was a little over 1/16th of an inch off center. Even on the lowest speed there was a lot of vibration. Luckily I was able to carefully scrape off the epoxy and gently pry the washer loose.

For the second attempt, I put a piece of masking tape on the fan hub, powered it on, then used a Sharpie to make several concentric circles. I then used a utility knife with the fan powered on to cut just outside the biggest circle so that the excess tape could be removed. I used the Sharpie circles as guides to ensure the washer was perfectly centered. I also used a hot glue gun to secure the washer rather than epoxy just in case it took more than one try. The second attempt was much more accurate and virtually eliminated vibration on all but the highest speeds.


Click here for Steps 6-7

Read more...

Stir Plate - Steps 6 - 7

6. The next thing I did was attach the magnets to the washer. I used the Sharpie to make a couple reference lines and temporarily taped them in place and tested for vibration. I then used hot glue to attach them to the washer.


7. The last step was just final assembly which consisted of attaching the box top, attaching a control knob to the rheostat, and finally adding a few silicone self-adhesive bumpers for feet.





Next up is ordering a stir bar and road testing the stir plate.

Read more...