Rood Mélange 2016

>> Sunday, January 03, 2016

It seems like I'm brewing sour beers half the time lately. I have some non-sour lagers queued up in the not too distant future, but my first batch for 2016 is yet another sour. Today I'm brewing a sour red ale based on the red base recipe from The Rare Barrel. This one will be fermented with Mélange - Sour Blend from The Yeast Bay. This is a blend I've never used before, but I'm excited to try it out. Per TYB:
Mélange is our most varied mix of fermentative organisms, intended for use in the production of sour beers in which a balance of funk and sourness is desired. This blend contains two Saccharomyces cerevisiae isolates, Saccharomyces fermentati, five Brettanomyces isolates, Lactobacillus brevis, Lactobacillus delbreuckii and Pediococcus damnosus.
For most of my sours I use aged hops. This time I'm going with a small addition of US Goldings. I'm interested in seeing how much this inhibits the lacto early on. Nothing too fancy with the water profile today, just cutting 8 gallons of carbon-filtered tap water with about three gallons of RO water. The recipe as I'm making it today:

6.0# 13 oz Dingemans Pilsner Malt
1.0# 3 oz Weyermann Pale Wheat Malt
7 oz Crisp Light Crystal Malt 60L
7 oz Flaked Oats (lauter)
7 oz Special Aromatic Malt
7 oz Spelt Malt
3-ish oz Carafa II (lauter, for color adjustment)
2.5g US Goldings (60 min)
5.0g Aged Debittered Hops (60 min)
0.5 Whirlfloc
Wyeast Yeast Nutrient
The Yeast Bay Melange Sour Blend
Mash at 130F for 15 mins, 158F for 45 mins, 90 min boil, ferment at room temp. Because of the lactobacillus, no aeration.

Brewing Notes
No real issues although my gravity came in a couple points low; target was 14P (1.057), measured was 13.7P (1.054).

Update 1/4/2016
I wasn't seeing any activity last night (24 hours after pitching) and I was getting a little worried. I had the fermenter in my basement which tends to be a little cooler than the rest of the house this time of year. I moved it upstairs last night and this morning I'm seeing active fermentation.

Update 1/6/2016
Fermentation is still plugging along. Krausen is at most one inch high, so no need for a blowoff hose as of yet. Aroma out of the airlock is a bit sour, but hard to say for sure.

Update 1/26/2016
Krausen has completely dropped and so far there are no signs of a pellicle. I'll probably let this go until at least April before pulling a sample.

Update 2/21/2016
I pulled a sample the other day. Tartness is fairly low, as would be expected with a young sour beer. One thing did surprise me a little bit, and that was an almost saison-like spiciness character. I hope this subsides over time because that isn't what I'm shooting for.

Update 5/14/2016
I pulled a sample of this beer last night. Still not digging the saison-like character, although it does seem to be mellowing. Sourness is still very low.

Update 7/18/2017
I pulled a sample tonight and I'm really happy with the direction this beer has taken. The saison-like character has essentially disappeared. There's a real nice acidity that has developed and the pH is coming in at 3.43. The acidity coupled with the fruity esters is really nice. There's some brett character there as well but it doesn't dominate. I'll be pulling samples from a few more reds soon and will probably be doing some blending.

Read more...

Mini-Mash Tun

Today I'm doing a little write-up on a new piece of equipment. a mini-mash tun. This isn't to be confused with mini mash or partial mash brewing; I'll still be doing 100% all-grain, just on a smaller scale.

There really isn't anything new or groundbreaking here, but I'm still excited about it. I've been toying with the idea of doing some smaller batch brewing for a while. Most of the time I brew 5 gallon batches and occasionally I'll mix in a 10 gallon batch, especially when I'm doing sours. Sometimes even five gallons of a particular beer can be too much. For example. pumpkin spiced beers...I enjoy them but they're hard to drink pint after pint so they tend to hang around for a while. I don't brew many lagers, mainly because I prefer the bolder flavors usually associated with ales. However, I'll probably brew lagers more often if I have the option of brewing smaller batches. Another candidate, beers that should be drunk fresh, like IPAs. Half batches will ensure tasty IPAs are finished off before the hops have a chance to fade.

So why a new piece of equipment rather than just making a smaller batch with my existing mash tun? Well, my normal mash tun is simply too large in diameter for batch sizes less than 5 gallons. It measures roughly 16" in diameter and the volume is about 12 gallons at the rim. This size vessel would have too shallow of a grain bed for 2.5 - 3 gallon batches. The new mini-mash tun is 12" in diameter and has a total volume of about five gallons, so the grain bed and liquid depths will be comparable to that of my larger tun. On the plus side, the 12" false bottom that I use in my larger tun will also work in the mini tun.

Weldless Assembly
Like my other brewing vessels, I'm going with weldless fittings on this tun. All the weldless fittings are based on Blichmann-style weldless fittings as documented on The Electric Brewery site. You can take a look at this diagram on The Electric Brewery for more details, but weldless fittings are assembled as follows (from inner to outer):
Hose barb nipple > full coupler > close nipple (through hole in kettle wall) > silicone o-ring > washer > nut > ball valve. 
As on my other vessels, I used my 13/16" Greenlee punch to make the holes for the weldless assemblies. These punches work awesome and give you a perfectly sized and perfectly round hole for mounting your assemblies. The false bottom connects to the nipple with a short section of 1/2" silicone tubing. The return from the heat exchanger is basically the same assembly and uses a short section of 3/8" silicone tubing to return the mash liquor to the top of the grain bed when recirculating.

That's about it for the mini-mash tun. I'm pulling my old 8 gallon boil pot out of storage for these smaller batches. I've outfitted it with a whirlpool port just like my keggle. I'm planning on the inaugural batch with this tun in the next week or so.
Return from HEX 

Full-size vs. Mini 

With False Bottom 

Read more...

Galaxy Microburst - Double IPA

>> Sunday, December 06, 2015

I used Galaxy hops in my American Brown Ale  couple weeks ago and the aroma was amazing. I believe this was the first time I've used Galaxy. I decided I'd like to try brewing a Double IPA to showcase this hop. The inspiration for this beer comes from Noble Ale Works' Showers series. Each release in this series focuses on a single hop variety. I've had the opportunity to try a couple releases and have really enjoyed them.

There isn't a ton of info available for cloning this beer. The best I've seen so far is in this thread (post #14). It'll be hard to say cloned or not cloned since I won't be able to do a side by side comparison, plus I'm shooting for a little lower IBU. Ultimately I'm just hoping for a nice drinkable DIPA that focuses on the hops. Keeping inline with the Showers theme, I'm naming my version Microburst after the intense localized thunder storms that tend to frequent Utah. I'm kind of going with my own take on this recipe, so I reduced bitterness somewhat and I'm using a different variety for the bittering hop. Here's the recipe as I'm brewing it today.

5# 11oz Rahr 2-row
3.5# Weyerman Pilsner
1.5# Golden Promise
1# 3oz Corn Sugar
28g Magnum (First Wort Hop)
56g Galaxy (1 min)
168g Galaxy (Dry Hop)
0.5 Whirlfloc
Wyeast Yeast Nutrient
US-05

Mash at 149F, 90 minute boil, ferment at 64F, dry hop after primary fermentation slows down.

For water profile I want something that will showcase the hops. I've heard very good things about Tasty's water profile, so this is what I'm shooting for today. To 10 gallons of RO water I added:

16g Gypsum (CASO4)
7g Epsom salt (MgSO4)
2g Canning salt (NaCl)
1g  Calcium Chloride (CaCl2)

Brewing Notes
No issues. Mash efficiency was a bit higher than normal at about 86%. The mash smelled fantastic, then the end of the boil was even better.

Update 12/14/2015
I pulled this beer from the ferm chamber yesterday and brought it into the kitchen to finish up fermentation. It still has quite a bit of krausen on top so I'll wait for this to drop before dry hopping.

Update 12/20/2015
I dumped as much yeast as possible today then added the 6 ounces of dry hops. This beer smells amazing. And here's what 6 ounces of dry hops looks like. After I took the picture, I ever so gently stirred the hop pellets in with a sanitized butter knife. I'll let these go for about a week then plan on transferring to a keg. Throughout the week I'll periodically give a little swirl to the fermenter.

Update 1/6/2016
This beer went into the keg tonight. I tried a sample that was cold but still flat...this beer tastes pretty amazing. I think it'll be fantastic when carb'd. Cold crashing dropped out the hop debris really well. I placed a sanitized paint strainer bag into the keg and then racked into it. This is the same procedure I've used with fruit beers. After filling, just carefully lift the bag out. It really seems to cut down on the amount of debris in the keg.

Update 1/10/2016
Still not fully carb'd, but I had some friends over yesterday to bottle our group brew Whiskey Barrel Russian Imperial Stout (aka Queen Jennie's Revenge) and I had them try this beer. The consensus was this is a pretty amazing and very drinkable DIPA.

Read more...

Steel-Belted Jockey Box Build

>> Wednesday, November 25, 2015

Back in June my club had a booth at the Mountain Brewers Festival in Idaho Falls, Idaho. All proceeds from this event go to supporting local charities in Idaho. We had about ten club members donate batches of homebrew which were poured right alongside commercial beers. This was the first time we'd ever done an event like this and it turned out to be a lot of fun. We had all 10 beers going from the start of the festival; four on tap on a borrowed jockey box (thanks Lauter Day Brewers!) and the rest using cobra taps. The cobra taps worked fine but they ended up turning into a sticky mess. The jockey box worked awesome, so it got me to thinking that I should start collecting parts in order to build one.

If you're not familiar with jockey boxes, they're essentially a portable kegerators. Rather than keeping kegs at serving temp, room temp beer is chilled on the fly as it's poured. This is accomplished by passing the beer through a cold plate or stainless coil packed in ice. It's basically a heat exchanger, pulling heat out of the beer as it passes through the cold plate.

Fast forward a few months and I finally have my hands on everything needed to complete my build. I wanted something more interesting than you're standard plastic ice chest, so I kept my eyes open for a vintage metal cooler.  I finally got my hands on a nice vintage Coleman cooler a couple weeks ago. This cooler is from the 70's, so it's not 100% metal, but I dig it. It definitely has more character than an all plastic cooler.

As for faucets, I found a member selling brand new ones on homebrewtalk a while back. These are standard chrome rear sealing faucets. I wouldn't recommend these on a home kegerator because they tend to dry out and stick between uses. However, they should work fine on a jockey box where they won't have time to dry out between pours.

For chilling I'm using a seven circuit cold plate. Since we have seven circuits and only four taps, three of the taps are plumbed to do a double pass through the cold plate, and one tap will do a single pass. The single pass tap will be used for beers that will benefit from a slightly warmer serving temp.

Cooler wall cross-section
The build is pretty straightforward; make holes for taps and supply lines then make all the connections. For the taps, I drilled pilot holes all the way through the cooler wall then used a holesaw to cut the interior plastic and my Greenlee punch to make a hole in the outer metal layer. I cut the interior hole big enough to fit a PVC plug that I'd drilled so the tap shank could pass through. The plan is to sandwich the fitting between the metal layer and the nut on the shank. This will allow me to really snug down the shank for a solid mount without worrying about crushing the inner and outer wall. The plug was epoxied to the interior surface of the metal layer and the joint between the PVC fitting and the interior plastic was sealed up with some silicone caulking.

I spent a lot of time trying to figure out how the best solution for the supply lines. I wanted a clean look, but didn't want to break the bank. I ended up going with stainless panel mount 1/4" MFL union/bulkheads. I'm really happy with the way these turned out, and they can even be disassembled fairly easily for cleaning, replacing lines, etc.

It's said the cold plates perform better when they're kept out of the water from the melting ice. You can buy cold plate holders, but I figured I could make a rust-proof holder out of PVC for cheap. I attached the holder to the cold plate using zip ties (not pictured).

That's about all there is to it. I just barely finished it so I haven't had a chance to test it out yet. I imagine I'll have to do a little fine tuning so I'll post an update once I have everything dialed in. In the meantime, here are a few pics of my build. Hopefully anyone planning a similar project will find them helpful.


Innards

Interior shank mounting
1/4" MFL bulkheads, exterior
Cold plate stand

Read more...

American Brown Ale

>> Monday, November 16, 2015

I picked up a copy of Gordon Strong's Modern Homebrew Recipes at GABF in September. Today I'm brewing a recipe from that book, American Brown Ale. I also have some company today; Chris Detrick from the Salt Lake Tribune joined me today for a video piece on Homebrewing in Utah. Chris is a very accomplished homebrewer himself so it was a lot of fun to have him on hand. I'll add a link to the video once it's available.

Updated: Here's a link to the piece. Chris did an awesome job with the editing. He took all my rambling and managed to put it together so that it made sense. It's funny because I'd planned on talking about all these different things, but when the camera was on, my mind went blank. It was much harder than I imagined to form coherent thoughts.   

American Brown Ales are a style I really enjoy. I don't brew them as often as I should, but they're a great style to have on hand. Moose Drool is one of my favorite commercial examples. The combination of caramel, toffee, and chocolate characters blended with fairly assertive hop character is something I really enjoy. Here's the recipe as I made it today.

10.0# Rahr 2-row
2.0# Avangard Munich I
1.0# Briess Crystal 60
0.5# Briess Crystal 40
0.5# Crisp Chocolate Malt (Vorlauf)
2.0 oz Weyermann Carafa II (Vorlauf)
28g Saaz (FWH)
14g Galaxy (15 min)
28g Sterling (5 min)
Wyeast 1272 American Ale II
0.5t Wyeast Nutrient
0.5 Whirlfloc

Mash at 151F for 60 min, 90 minute boil, ferment at 66F.

Water treatment - Per the recipe in the book, I'm using RO water and adding 3.4g (1t) CaCl to the mash. I'm still learning about water chemistry, but this just seems too simple...regardless, I'm going with it.

Brewing Notes
No issues with this beer. Dark grains were added once we started running off to the boil kettle; at first I was a little worried because it wasn't picking up much color, but that changed after a few minutes. With the cooler temps this time of year, we were able to chill down to pitching temps fairly quickly.

Update 11/18/2015
I had to hook up a blow off tube this morning. This yeast produced a very dense mousse-like krausen that slowly crept higher and higher. It finally pushed up through the airlock sometime late last night or early this morning.

Update 12/5/2015
I decided to dry hop with the remaining 14g of Galaxy. This was added today.

Update 12/14/2015
This went back into the ferm chamber yesterday for cold crashing. I'm hoping to keg it later this week.

Update 12/20/2015
I kegged this beer today. The aroma coming off this beer was fantastic, hoppy with some really nice malty complexity. As with most of my kegged beers, I primed it and will let it naturally carb over the next couple weeks.

Read more...